Click here to download Spec Sheet The Independent Puffy Vest has plush warmth for all seasons. With a nylon shell, Hyper-Loft synthetic insulation power, zippered pockets, and a packable inside chest pocket, gives versatile function, making it ready for any adventure. Water & wind resistant 100% Nylon exterior shell 60 gm Hyper-Loft poly fill insulation 100% polyester lining #5 reverse coil zippers at chest and pockets packable pocket with #3 reverse coil zipper capped elastic armhole binding lockerloop at wearers back neck plastic cinche toggle at wearers right side waist tear away neck label chest pocket for concealed embroidery access

Click here to download Spec Sheet Our EXP35SSZ is a water resistant and wind resistant Poly-Tech soft shell jacket with a concealed embroidery access for embellishing. Made to protect you from the elements, the soft polyester exterior fabric with Waterproof lining keeps the weather out, a bonded Micro Fleece interior lining gives comfort and warmth, a scuba hood for good coverage, water resistant zippers with interior wind blocking flap, welt pockets, and drawcords with toggles at hood and waist. This fabric is waterproof however, we give this jacket a water resistant rating since the seams are sewn not glued/taped/waterproofed. 13.8oz/460gm total weight 300 gm 100% waterproof polyester shell bonded to 160gm micro fleece lining. Waterproof Coating: 20,000 mm Inner PU Coating: Breath-ability/Permeability = 5,000 3 panel scuba hood #5 water resistant zippers zippered left chest pocket and welt pockets media pocket toggles at hood and bottom side seams antique nickel eyelets concealed embroidery access for embellishing tear away neck label Please Note: Low cure poly ink & poly blocker recommended. Keep garment temperature under 300°.

Click here to download Spec Sheet The EXP550Z is a classic workwear jacket… Built to last with a Rugged 360gsm 100% Cotton Canvas shell with Hyper-Loft quilted insulation, 3 panel hood & heavy duty brass zippers. This jacket has a tear away label, locker patch in the center back neck for printing or sewing neck labels. It also has a 23” wide hidden zipper that provides print & embroidery access to the inside of the garment. This hidden access enables you to print multi colors with no registration problems, and hide the embroidery backing between the shell and quilted interior. This is a major plus if you are decorating these garments. 360gm 100% cotton canvas shell Hyper-Loft quilted insulation 3 panel hood heavy duty brass zippers 2x2 ribbing at cuffs & waistband tear away neck label

Click here to download Spec Sheet This Nylon Water Resistant Windbreaker Anorak Jacket is screen print friendly, and has waterproof nylon fabric. The Nylon exterior fabric is coated with a 100% water proof coating... however, we give this jacket a Water Resistant rating since the seams are not waterproofed, which may allow water to eventually enter through the seams when exposed for extended periods of time in a downpour. 100% nylon 330D with Interior PU waterproof coating Nylon Outer Shell: Waterproof Coating = Level 3 Inner PU Coating: Breathability/Permeability = 5,000 Water Pressure Resistance = 10,000 mm DTM neck taping tear away neck label #5 DTM body coil zipper matte metal zipper pull rubber zipper pull tab zipper garage fine mesh hood liner matte nickel metal eyelets 3 panel hood scuba neck round poly drawstring hidden snaps inside front pocket flap side slit pockets tightening toggle at waistband elastic cuffs Please Note: Printing Notes: Use a nylon or plastisol ink with a catalyst (hardener). Certain Poly Inks can work as well. Ask your ink supplier. Keep in mind a catalyst will shorten the shelf life of the ink leaving left over ink unusable as it will harden. Use tight screens with 200+ mesh count to lay down a little less ink than would be used on tees (tees normally use a more open mesh like a 110). Ink tends to sit on top of the surface of this fabric as opposed to pressing into cotton type fabrics. A harder squeegee can help lay down less ink and help keep cleaner design edges. Nylon fabric also tends to move more than tees on the printing pallet. Sometimes a jacket clamp is recommended when doing multi-color prints. Curing time and temperature will vary by ink types used on nylon fabrics. VERY IMPORTANT to cure your ink at the right temperature without burning or shrinking nylon. Nylon fabrics should usually be cured at temperatures under 320. Flash at low temperatures to keep from burning and/or shrinking fabric. (consult ink supplier and test). Washing the printed sample garment(s) after 24+ hours (so hardener has set) is recommended to make sure you have proper curing and ink adhesion. *ALWAYS consult your ink supplier for the right ink, cure temperatures, and curing time. Then run your own test sample(s)

Click here to download Spec Sheet This Nylon Windbreaker Coaches Jacket is screen print friendly, and has waterproof nylon fabric with snap front closure. The Nylon exterior fabric is coated with a 100% water proof coating... however, we give this jacket a Water Resistant rating since the seams are not waterproofed, which may allow water to eventually enter through the seams when exposed for extended periods of time in a downpour. 100% nylon 330D with Interior PU waterproof coating Nylon Outer Shell: Waterproof Coating = Level 3 Inner PU Coating: Breath-ability/Permeability = 5,000 Water Pressure Resistance = 10,000 mm unlined hood self neck tape tear away neck label antique brass eyelets (black/black color = matte black metal eyelets) antique brass 6 snap front closure (black/black color = matte black metal snaps) elastic cuffs underarm grommets drawcord closure at hood and bottom opening standard fit Please Note: Printing Notes: Use a nylon or plastisol ink with a catalyst (hardener). Certain Poly Inks can work as well. Ask your ink supplier. Keep in mind a catalyst will shorten the shelf life of the ink leaving left over ink unusable as it will harden. Use tight screens with 200+ mesh count to lay down a little less ink than would be used on tees (tees normally use a more open mesh like a 110). Ink tends to sit on top of the surface of this fabric as opposed to pressing into cotton type fabrics. A harder squeegee can help lay down less ink and help keep cleaner design edges. Nylon fabric also tends to move more than tees on the printing pallet. Sometimes a jacket clamp is recommended when doing multi-color prints. Curing time and temperature will vary by ink types used on nylon fabrics. VERY IMPORTANT to cure your ink at the right temperature without burning or shrinking nylon. Nylon fabrics should usually be cured at temperatures under 320. Flash at low temperatures to keep from burning and/or shrinking fabric. (consult ink supplier and test). Washing the printed sample garment(s) after 24+ hours (so hardener has set) is recommended to make sure you have proper curing and ink adhesion. *ALWAYS consult your ink supplier for the right ink, cure temperatures, and curing time. Then run your own test sample(s)